INSTRUCTIONS OF USE FOR

Safe Plus

Nitrile examination gloves

EDMA GROUP, LLC
3634 PICCADILLY RD,
PHEONIX, AZ 85018

Edma Safe-Plus Gloves
INSTRUCTIONS OF USE FOR

SAFE PLUS

Nitrile examination gloves

EDMA GROUP, LLC
3634 PICCADILLY RD,
PHEONIX, AZ 85018

EN 420:2003+A1:2009 / EN ISO 21420:2020

     

WARNING: SINGLE USE GLOVE

1. Safe Plus EDMA NITRILE EXAMINATION GLOVES

This product has been manufactured following the requirements of Regulation (EU) 2016/425, for its basic use, according to the standard EN 420:2003+A1:2009 / EN ISO 21420:2020 (Protective gloves — General requirements), EN ISO 374-1:2016/A1:2018 (Protective gloves against dangerous chemicals and micro-organisms – Part 1: Terminology and performance requirements for chemical risks) and EN ISO 374-5:2016 (Protective gloves against dangerous chemicals and micro-organisms – Part 5: Terminology and performance requirements for micro-organisms risks), as stated in the certificate No. UE-000035/00 issued by Eurofins Textile Testing, C/ Germán Bernácer nº 4, 03203 Elche-Alicante, Spain, Notified Body No. 2865.

This PPE is made of the following materials: Powder-free blue Nitrile.

IT IS RECOMMENDED THE USER READ THIS MANUAL CAREFULLY AND TO FOLLOW THE GENERAL INSTRUCTIONS.

THE MANUFACTURER DISCLAIMS ALL RESPONSIBILITY FOR DAMAGES OR DETERIORATIONS CAUSED BY UNAUTHORIZED MODIFICATIONS MADE TO THE PPE BY THE USER.

2. WARNINGS AND LIMITATIONS OF USE
  • Dirt or substance residues adhering to the glove can impair its performance.
  • Protective equipment does not act as a chemical barrier at the molecular level.
  • The glove has to be removed carefully to avoid any product residue left on the surface of the PPE from coming into contact with the skin.
  • Carry out an inspection before putting on the PPE to ensure that it is in perfect condition.
  • This product does not offer protection against gases and vapors.
  • The user must know the use and handling of the glove.
  • This product must not be used against risks other than those described above.
  • EN 374 -4:2013 Degradation levels indicate the change in puncture resistance of the gloves after exposure to the challenge chemical.
  • “This information does not reflect the actual duration of protection in the workplace and the differentiation between mixtures and pure chemicals.”
  • “The chemical resistance has been assessed under laboratory conditions from samples taken from the palm only and relates only to the chemical tested. It can be different if the chemical is used in a mixture.”
  • “It is recommended to check that the gloves are suitable for the intended use because the conditions at the workplace may differ from the type test depending on temperature, abrasion and degradation.”
  • “When used, protective gloves may provide less resistance to the dangerous chemical due to changes in physical properties. Movements, snagging, rubbing, degradation caused by the chemical contact etc. may reduce the actual use time significantly. For corrosive chemicals, degradation can be the most important factor to consider in selection of chemical resistant gloves·”
  • “Before usage, inspect the gloves for any defect or imperfections.”
3. PROPERTIES. The higher the class, the greater the protection
Penetration
EN 374-2:2014 Air Leak / Water Leak PASS
Permeation performance level
Measured breakthrough time Permeation performance level
> 10min. Level 1
> 30min. Level 2
> 60min. Level 3
> 120min. Level 4
> 240min. Level 5
> 480min. Level 6
PROTECTION AGAINST VIRUS EN ISO 374-5:2016
ISO 16604, Procedure B PASS
CHEMICALS EN ISO 374-1:2016/A1:2018
Code Chemical CAS number
K Sodium hydroxide 40% 1310-73-2
P Hydrogen Peroxide 30% 7722-84-1
T Formaldehyde 37% 50-00-0
Chemical Level
EN 16523:2015 Permeation Sodium hydroxide 40% (K) 6
Type B Hydrogen Peroxide 30% (P) 4
KPT Formaldehyde 37% (T) 4
Chemical Mean Degradation %
EN ISO 374-4:2 013
Degradation
Sodium hydroxide 40% (K) -7.4%
Hydrogen Peroxide 30% (P) 25%
Formaldehyde 37% (T) 41%
4. SIZE CHART:
Size Hand circumference (mm) Glove length (mm)
6 152 220
7 178 230
8 203 240
9 229 250
10 254 260
11 279 270
5. DEXTERITY: LEVEL 5
6. STORAGE AND PACKAGING.

Store the glove avoiding unnecessary sun exposure and in dry places, protected from any aggressive agent.
The gloves will be packed in boxes.

Keep out of sun

Keep dry

Temperature limited
(5ºC-35ºC)

Do not use if packaging is damaged

7. USEFUL LIFE AND OTHER SYMBOLS.

Store the glove avoiding unnecessary sun exposure and in dry places, protected from any aggressive agent.
The gloves will be packed in boxes.

The glove has a useful life of
3 years

Year of manufacture:
11 / 2020

Batch Code
E1E48021D01AH

Latex free

Non sterile

8. DECLARATION OF CONFORMITY: WEB or QR code
EU-DOC-EDM001
Back to Product Page
View Certificate
Back to Product Page